here it is|
|29-06-2012||SANSUI SR-535 repair manual||I have that same tt and the same problem.
I found the service manual on vinylengine. Requires a profile sign-up that is free.|
|29-06-2012||Re: no power||[quote:732dd9730d="rukodaime"]same here i need manual for this model 21v-fw600s because replace too str-w5453 because its the original part number ...but nothings happen...no progress i observe[/quote:732dd9730d]
try to replace exact value or any value|
|29-06-2012||If you get any response, please let me know, i'm also looking for that service manual.
Thanx in advance.
my e-mail : [email protected]|
|29-06-2012||LG55LE5400 TV issue with power up||Recently, I believe my TV stop working. I was watching tv and the screen went black and no sound. One thing I noticed is that the standby light is still on. I can turn the TV on and off with either the remeote or on the TV itself, but no picture. Fuse is |
|29-06-2012||I believe FW-C355 is not the same as FW-355. They are different models.|
PS usually sparse in coverage.|
|30-06-2012||Philips 46PFL5505D/F7 conversion to 46PFL5705DV/F7||Hello,
I was wondering if it's possible to swap the mainboard (A01Q5MMA-001) from my 46PFL5505D/F7 with one from a 46PFL5705DV/F7, main CBA model # A01QCMMA-002? (since they're are same PL10.7 chassis)
Would the connections to the Function, IR, and |
|30-06-2012||Dell M993s CRT Flyback Pinout||Hello, I have an old Dell m993s crt monitor that I have removed the FBT from to use for a little experiment of mine. I thought I would be able to just punch the id number in and find a pinout or datasheet, but alas, I cant find anyhting. I have found a ra|
|30-06-2012||Google "LEO PROJECT 11 Schematic" and You'll find your flyback 8)
|30-06-2012||Much appreciated! But now my problem is I cannot make heads or tails of the connections. First they're are only 14 pins. I cannot find a 15th. Secondly it doesnt show a connection to the HV output. When I apply voltage to the various pins trying to figure|
|01-07-2012||There is always a possibility of a bad fly but you must have the polarity correct. Are you trying to make a high voltage arc? The extra pin could be the center (around the core) or may not even be there?
Here is a link that shows how to find the pins.
|02-07-2012||phillips tv||where can i find the repair kit???|
|02-07-2012||Toshiba TP50H50||I found this post after a lot of searching about the net. My TV is a Toshiba TP50H50 and has a similar board layout and components. I wanted to post this to say thank you to Minnie and Centralmarc for the photos and helpful advice. Our set had the dreaded|
|02-07-2012||Toshiba TP50H50 blinking red light||Just repaired my Toshiba TP50H50 using information from a thread here concerning the Toshiba TP55H60 by Centralmarc. Just tried to link to it, but got an anti-spam message.
Similar configuration and very helpful images and comments.
Thank you! I|
|02-07-2012||Toshiba TP50H50||BTW, I chose to cut away a 2" section of the plastic support tray once I had the electronics tray on its back. This seemed an easier way to access the pins on the LA7833 IC than removing the board from the plastic carrier tray. I had to unplug 3 conn|
|02-07-2012||Toshiba TP50H50 blinking red light||Another BTW for you first-timers. Once you have the electronics tray moved out a bit, you'll find the vertical IC just to the right of center toward the back of the tray, connected by a screw to an aluminum heat sink, just to the right of a roughly 4x4&qu|
|02-07-2012||Asus MK241H service manual||Hi to everybody, new on this forum, coming from badcaps to ask a favor.
I'm trying to fix this monitor, but I'm stuck without schematics.
Found already Q101 FET shorted, which I have replaced, I have also replaced all the capacitors w/Panasonic FM/FC on|