|no luck...now there is just no color as soon as I turn the set on. Any other suggestions?
|Toshiba 27A51 Trouble powering on
|Working on a Toshiba TV model 27A51. When I try to power it up the deguass relay will cycle every few seconds for a while. After the relay stops cycling the I can turn the TV on it plays fine. The TV will play for 2 - 3 days then it will go out and the re
|Sony TV dead. Only front led blinking 11 times every 2 secs.
I was browsing the interbet looking for a solution to a current problem to my tele and came across this website.
It's a Sony TV FE2 chassis KV32LS35U
You might have guessed, yes, it's the front LED, which flashes 11 times and then repeats
|Thanks for the link!
Checking it out...
|So now no tubes are lighting?
|C531 470mfd 16v is usually the culprit. The cap dries out and eventually it wont start at all. Super size it to 25v.
|Press display, #5, channel up and power on the remote and see if it comes on. Or the last set could be volume up.
|Theres a couple on ugh I hate to say it eBay starting at around $450.
But with eBay Caveat Emptor! (let the buyer beware)
|Sound Localization, MC, and Neural Network
|Currently I am working on my final project. My final project title is “Design and Implementation of Mobile Robot Sound Tracker Based on Artificial Neural Network”.
I want to make it embedded with battery as the supply.:D
Any idea where should I lear
Great idea! I tried it, but unfortunately the same problem. Any other suggestions would be much appreciated.
|replace the ic close to the flyback.16 or 18 pins for high voltage startup.---3001.
Cory you mean IC 6501When you say 3001=MZ3001?
|Thank you for the quick responses, I did suspect that it was a bad IC but I am weary in removing the board as I would need to discharge the crt.
The stand-by light blinks six times when off and seven whnen it tries to go on.
I think it will be wis
|LOW +B OCP/OVP
6 times 6:0 or 6:1 • +5 line is overloaded. (A, B, M Boards)
• +5 line is shorted. (A, B, M Boards)
• IC504 is faulty. (A Board)
• No picture
7 times 7:0 or 7:1 • No picture
|Toshiba 35AF44 picture alignment...
|I have a Toshiba 35AF44 that is brand new but purchased from a AV house straight from the box. After unwrapping it & trying it out I noticed that the graphics were not straight on the screen. The image fills the screen, but is about a 1/4" high o
|sorry, mistyped...only the blue tube is malfunctioning. So changing the voltage didn't help.
|I have a toshiba tp71g90 that was still working great until this morning I turned it on and came back 5 mins later and the screen was off and the front power led was blinking. I have tried unplugging it etc... and it will click like it is turning on when
|PROBLEMS WITH A MAGNAVOX MS3252S431
|HI THERE, I WILL LIKE TO HAVE SOME HELP WITH THIS TV PLEASE, MY PROBLEM IS THAT I HAVE A HORIZONTAL PICTURE SIZE PROBLEM, IS TO SMALL AND I CANT FIND HOW TO GET IT BIGGER AFTER GET IN INTO THE SERVICE MODE THIS IS WHAT APPEAR AT THE PICTURE ON THE HORIZON
|Grundig Beta4 code help
|Please, help for Grundig BETA 4 Code, S/N VWZ2Z2S5372702,
made by Grundig Portugal. Thanks for any help. -ivano-
|Hi, I sent to You 12 mb radio codes programs.
|disassemble toshiba satellite pro 4600 to clean heatsink
|hi... about a month ago my laptop started to play rpg game erratically...
i installed the game and new drive D... same thing.. i got speedfan 4.33 and set fan on at 100 %... the game plays ok with it on and the cpu at about 55 degrees... when doing this
|NO IDEA, IT IS NOT AVAILABLE IN THE UK. BEWARE ITS NOT THE HEAD YOU REQUIRE BUT THE DRUM ASSY.
|the mechs in that model are horrendous to set up, i was told once that denon actually withdrew them from sale because of the problems, the manual is a complete waste of time, it goes into detail on how to install 2 of the trays but does not even mention t
|Philips LCD monitor model 200P3
|This has no picture, The inverter board has a blown surface mount fuse F1 - I need to know the rating of this fuse please.
The power LED behaves normally, ie green with signal, amber without.
A copy of schematic would be handy if someone has one.
|thanks alot minnie !!I will replace tuner . :wink:
|creating a dummy circuit for impedance analysis?
|I need to make a simple RC circuit made up of 3 resistors and 2 capacitors in order to validate data being given by a Solartron 1260 Frequency Response Analyzer (FRA). It is constructed with 1 resistor in series with 2 series RC circuits. The values of
|Cleaning TV boards / Modules
[b:79c5707d21]Hello folks, I got some good tv modules / boards that are not
that clean, what is a good cleaning spry that remove most of
the dirt, without affecting the parts / coils, etc.[/b:79c5707d21]
|New Forum..............Start Posting!
|40 turn trimmer potentiometers
|Where can I buy 40 turn Potentiometers for replacing old pots on a Pioineer Spec II amplifier.
|canon elura 100 schematic
|Anyone have the schematic for the Canon Elura 100?
|goldstar microwave oven model mv-1140t
|Does anyone know where I can get a manual for the Goldstar Microwave Oven Model # MV-1140T? I've contacted LG and they don't have it.
|It is possible to get low value resistor & higher value caps.("super caps" are within that range") As far as resistance, you are dealing in super low value territory which is practical with SMD stripes--- mainly used in high precision m
|TROUBLE WITH TV SONY KV-X2130B
when i want to record something,it's in black and white.
When A/V is selected,tv is in black and white.
|Again thanks .... Is there any way that I can get a schematic of this tv .. I have no idea were these IC are located ...
I did poke around the D board and moved a few of the capasitors and litle gizmos and the tv came on without having to heat it up .
|RCA P52927 convergance out of alignment
|[b:23e264915a]I have an RCA 52"projection screen tv.....the color is off....on images...in texts, red,yellow,blue, lines outside the image.
I believe, from all the posts I've read so far its the convergancy circuit board. how do we get this fixed??
|who did you send them to?