Date | Header | Text |
19-08-2009 | Pioneer RX-760, RX-560 stereo system service manual. | Hello! I need a service manual or schematic diagram for the Pioneer RX-760 or RX-560 setero system. I am interested mainly in the output stage.
Thank you,
Andy. |
19-08-2009 | | eserviceinfo.com/downloadsm/43449/SONY_TA-AV501.html |
19-08-2009 | Puzzled | Hi again -
After closer inspection, here's what I found:
All power supply voltages are OK with power relay bypassed.
Standby and System Off buttons do not power up unit.
Of course, no display, although voltages on FD pins and controller seem |
19-08-2009 | | eserviceinfo.com/downloadsm/43454/SONY_STR-D990.html |
19-08-2009 | Help Me On Urgent Basis | Please help me on urgent basis regarding Service and programming manuals of Panasonic Photocopiers model DP-3510 on urgent basis kindly help or give the link of mention subject. |
19-08-2009 | | Hi minnie. What can be bad on a such main board to produce a such effect ?
Replacing a board ain't real troubleshooting, is it ? :) |
19-08-2009 | | Thanks for the info. I guess the problem lies elsewhere. At least I get to practice soldering. I already desoldered and pulled the old caps out. I'll put it back together and post a pic of what the screen looks like. I'm just not sure what board to troubl |
19-08-2009 | | Anyone know if this fuse repair works too on a Denon UD-M5 with triple CD changer? My symptoms are similar to what happens when fuse fails. But looking at the photo thumbnails mine seems a very different PCB layout. Any chance of gets the link to those ph |
19-08-2009 | please | please please help me as you can |
19-08-2009 | | I hate to say it, but it sounds like a bad Micro. |
19-08-2009 | 42LC2D LG no picture | The picture just went out on this TV, but the sound still works. Is there anything I can do to save this unit? Fuse? |
19-08-2009 | | Electronic balance? did you mean Ballast?
Perhaps a UNxx series rather than 2Nxx. Never seen a 2N series labeled w/out the 2 |
19-08-2009 | | What's the record for the longest time between initial post and first (serious/valid) reply :?: |
19-08-2009 | | Not sure of the record but since it was started sometimes back in 2004, anything around that time can be considered as a record. :wink:
Majority of the time though, it is simply a reply to some sort of a search without even looking at the original posti |
19-08-2009 | | This Parts & Service manual can now be purchased for $11.77 and downloaded immediately after payment from http://www.justmanuals.com
[email protected] |
19-08-2009 | Toshiba H65HX81 projection tv | Looking for service manual.
Found what part might be bad, just clicks.
No picture or sound, red light comes on when power button is hit but that is it.
Toshiba H65HX81 projection tv |
19-08-2009 | Fujitsu plasma SOT ID | I have a PDP driver board and I need to ID 2 components They are a SOT case with 3 lead on one side and 1 on the other internally connected to the middle lead. The SOT drives the FET outputs. The markings are FX-16 on one device and EY-16 on the other |
19-08-2009 | Altec Lansing Sub of computer speakers | My wife accidentally shorted the input line which has caused a 60 cycle hum that increases when the bass is adjusted up on the speaker control. The capacitors have tested good, but I am unsure how to test the amplifier circuit. The circuit has three trans |
19-08-2009 | | how did you test the caps? a regular DMM that has a cap. setting doesn't really mean anything. |
19-08-2009 | | UTC2030 is not a transistor. It is an audio IC that can be used in various configurations and there is no standard way of testing the device. Just about all you can do is to pull up the data sheet and do a voltage testing which wont tell you much.
What d |
19-08-2009 | | There is a post relating to the UD-M5 here http://www.fogma.co.uk/electronics/353.html about various faults apart from the eject failure. It mentions a similar fuse setup to UD-M3.
Also there are posts in Japanese with lots of PCB pics that show the fu |
19-08-2009 | | Is now OK. Found that I had left one of the trillions of connectors unplugged under the CD changer unit so none of my new found 12V was getting to the eject motor. If you follow the correct instructions here you don't need to do much dismantling on a M5 ( |