Date | Header | Text |
03-06-2008 | Grundig TV and DVD problems | Hi all!
I have two problems with Grundig products. A TV and a DVD.
1)Grundig CUC 7303 (20” CRT).
When I power it on the led starts blinking and I am hearing a tick-tick-tick from the loudspeaker. Nothing more. I took some measurements:
Main filter |
03-06-2008 | Philips mg2.1e chassis low brightness , no blue raster | I have a Philips mg2.1e chassis which has low brightness and it hasn't got blue raster.
Please can anybody help me. |
03-06-2008 | | I'm really not happy with the way the blue is showing on the screen at the moment.
I have a couple more STK392-040's here. Could it improve it if I change the blue one over perhaps? |
03-06-2008 | | In both cases, the fault is most likely a short somewhere on the secondary side of the power supply.
Check all output voltages for shorts. In the tv, a common cause for this kind of problem is a shorted line output transistor, possible as a consequence o |
03-06-2008 | | up |
03-06-2008 | | Check that all three CRT heaters are glowing normally.
Also, check the drive to the CRT cathodes by a scope. If the drive signals are normal (both p-p value and dc level, no black clipping etc), then the CRT is probably faulty. Of course, you could try t |
03-06-2008 | JVC DRM1SLB 'LOADING' Flashing on display. | HI,
Every time i power up this machine it flashes 'LOADING'on the display panel and, well, thats it!!! front panel buttons are non-responsive and it wont even open the tray.
Any ideas ?? |
03-06-2008 | Sony KV-X2982U shows no picture but has OSD and sound | Has anybody seen this problem:
No picture it looks a bit like it's warming up except for two faintly white patches at the top left and right of the screen.
The sound is ok and the OSD works except there is no white (shows as yellow) or blue (shows as |
03-06-2008 | Sanyo DS31590 no picture w/ dvd player | I have setup a basic DVD player into my Sanyo TV, all cables are in correct, (yellow, white and red), when I place a dvd into the player I can hear the sound but my tv still plays regular tv? I have done this many times before with other tv's, normaly I s |
03-06-2008 | Need Data Sheet and registers description for MB8739AE | Hi,
Can anyone help me to give the datasheet for old Position Control LSI MB8739AE (Fujitsu-Fanuc)?
Thanks |
03-06-2008 | Re: LC 4341 | [quote:77042a4005="toudy"]1/ check DC value (+295V DC aprx.) on the PowerSupplyBoard unit -output DC power for ballast unit
2/ check switch door, dust filter switch (1914), all connected fans (1913, 1912, 1914, 1911, 1910) and their functionality, check |
03-06-2008 | | Answer to that is Nope.
Changed the IC over and is still the same. Blue is blurry and doesnt seemed to be repairable with the Focus/Saturation/Lens dials. :(
It probably is, but it eliminates the Perfect focus, and is still very slightly off (notic |
03-06-2008 | Re:problem with Sanyo DP32746 | I checked out the set again today. If I shine a bright flashlight into the screen at an angle, I can see pixels and movement, so I think the panel is ok, however, I suspect there may be a problem in the inverter board as I checked F100 on the inverter boa |
03-06-2008 | | If the fuse is open you can try to replace it. It will blow again. Sanyo's #800-877-5036. |
03-06-2008 | twf lcd tv user manual | hi, anyone know were i can get a user manual for a twf lcd tv 26411d. thanks shane. |
03-06-2008 | | Swap leads on the screen/focus block. In other words follow the blue screen/focus wires and swap them with the red or green screen/focus wire and put the red or green wires where the blue came from. I'v had bad focus/screen blocks before. |
03-06-2008 | | What if you run it in RF? Sounds like the video IC isn't selecting. |
03-06-2008 | | Doesn't the service manual give you the part numbers? |
03-06-2008 | | $130/$180. |
03-06-2008 | Phillips Convergence or HV Block/Splitter | Hello
I have a Phillips 50in Projection TV:
model: 50P8341
chassis: PTV-915
The picture is very blurry and you can't make anything out.
If I adjust the color for the green and red tubes the image clears up ,but the blue tube stays blurry. |
03-06-2008 | | Swap focus/screen leads on the block to see if it's the block. Swap green and blue. Who changed the fluid? When I do these I do both the green and blue. Red doesn't grow the algee. It looks like contaminated fluid to me. It's not convergence. |
03-06-2008 | | Hi
I bought the TV from someone and they said the fluid was changed.
I took out some fluid out of the blue tube and it's crystal clear.
How exactly does contaminated fluid look like?
I will try swapping the screen/focus leads on the block.
|